Electrical Fault Detection Services

So you think you could have a problem with the electricity and you are not sure exactly what is wrong. We provide a comprehensive electrical fault detection service so no matter what the problem is, we will find it. You don’t need to worry, if you suspect the issue could be dangerous, the first thing to do is make sure everyone stays away from the area. 

​You can call us and tell us exactly what is going on and we will advise on the best, safest approach. You may be asking ‘what is wrong with my electricity?’ and the short answer is ‘we need to have a look to be sure’. So the most efficient way to proceed would be to firstly get in contact with us and let us know as best as you can exactly what’s happening. When we can establish roughly what the situation is we can send over one of our Ballarat electricians.

​When we arrive we will have a look at the situation and if it requires electrical repairs we will provide you with a free quote on the spot. Feel free to call us anytime you need an electrician to help you find out what is wrong. 

What is involved during electrical fault detection?

This involves a systematic approach that starts with observation of the system. By analysing the performance of an electrical system, detecting any inconsistencies or problems that may exist, and then taking appropriate steps to address the issue. Fault detection can help prevent costly repairs, damages and potential safety risks associated with faulty wiring or malfunctioning components.This can involve noticing any unusual noises, smells or sparks coming from the equipment or noticing any changes in performance such as excessive heat or voltage fluctuations. From there, we may use specialized test equipment to measure electrical parameters such as current, voltage and resistance levels, to identify any irregularities in the system. This data can then be further analysed to identify a specific fault.

​When a fault is identified, we can use our experience and expertise to determine the best course of action for addressing it. Depending on the nature of the fault, this may involve repair or replacement of components, rewiring or other corrective measures.

Electrical Services we provide

• Residential Electricians
• Commercial Electricians
• Emergency Electricians
• Electrical Maintenance

Electrical Emergency services

• Electrical Repair Services​
• Electrical Fault Detection
• Switchboard Services
• Surge Protection Setup
• Emergency Exit Lighting
• Blown Fuse Repairs
• Power Outage Services 

Types of Electrical Faults

You will want to keep a look out for common problems that can occur within a power system. It is always good to have some basic knowledge about things so when they do pop up, you are better prepared to deal with it. Here we have listed the most common problems that need attention.

Flickering Lights

Electrical Surges

If you notice lights are flickering this could be for a few reasons. Firstly the most obvious is that the light bulb is actually loose and not properly connected. You will want to make sure the light is off for a while before touching it otherwise you will burn your fingers. Once it has cooled down try to tighten the light bulb in the light fixture. Afterwards, if there is still an issue, give us a call and we will find the problem.

Power surges are common and have multiple reasons as to how they come about. The main issue is too much electricity getting into the system. This could be due to lightning, power line issues, a broken appliance or even house wiring that has become faulty. Again, if this is a problem that continues and you are unsure of the cause, give us a call.

---

Circuit Overload

Sparking Power Points

This is most likely because there are too many electrical appliances plugged in using the same power point. Each power outlet can only let out a certain amount of power, so if you don’t have enough, we can install more for you. A common problem is people daisy chain many power boards together that all use the same plug. This will trip the circuit, causing an overload, and so the power turns off. You can turn it back on in the meter box after removing some appliances from the chain.

You may have a power point that is sparking when you plug something in and it’s not switched on. This is a classic electrical fault that needs to be fixed by an electrician. You may think the appliance is off because you have turned it off at the wall, but if the power point is broken, the appliance may still be getting power. The worst place this can happen is in the kitchen with a toaster or sandwich press connected. Get in touch and we will fix it right away.

For any electrical faults, repairs, fixes or any problem that needs a local electrician in Ballarat, give us a call now.